【T-N.T. APS-X HOP-UP SYSTEM】
WE GLOCK series GBBP FULL HOP-UP RETROFIT KIT 

​【TAIWAN T-N.T. STUDIO】 2023年 全新產品 !!
『THE ONE』
WE GLOCK系列 GBB手槍專用 一體式 TDC HOP-UP座總成 / 成套套組

對應型號Corresponding model：
●WE G series G17/18/19/23/34/35 (if G26/27 please specify in the order, the chamber is shorter)
●MARUI original HOP-UP unit, not suitable for New ver. HOP-UP unit (side adjustment)
●VFC older ver. HOP-UP unit (similar to TM spec.), not suitable for New Front-guide ver. HOP-UP unit

產品特色：
1. HOP座本體為一體式設計並採用合金精密鑄造，膠皮全包覆式的設計氣密度優秀且安裝步驟簡單快速。

2. HOP座本體側面最容易斷裂的部分：滑動輔助定位凸點，改為使用鋼製的PIN代替，堅固耐用再也不斷裂。

3. HOP-UP調整方式改為TDC方式：
●可提供調整環平均的下壓力度，徹底擺脫傳統下壓鋼片設計之左右受力不均問題。
●HOP無段式調整，可進行更細緻的微調；更大的HOP調整範圍，不論使用輕彈或重彈都可輕鬆駕馭。
●調整環設計有回推彈簧，維持HOP-UP不易鬆動，有效維持調整完畢後的理想下壓量。

本產品提供以下可供選購：
●單HOP-UP座套組 (標配為H.L.R.或可更換T-HOP膠皮)。
●HOP-UP總成套組 (標配為H.L.R.膠皮、精密管、HOP座)。
​※220mm以下內管皆無氣墊槽設計※
-
【TAIWAN T-N.T. STUDIO】2023 New release products
『THE ONE』
WE GLOCK series GBBP dedicated One-piece TDC HOP-UP chamber assembly / Complete set

Features :
1. The body of the HOP chamber is designed in one piece and made of alloy precision casting. The rubber-covered design has excellent air-tightness and the installation steps are simple and fast.

2. The part that is most likely to break on the side of the HOP chamber : the sliding auxiliary positioning bump is replaced by a steel PIN, which is durable and will never break.

3. Change the HOP-UP adjustment method to TDC :
●It can provide the average down force of the adjustment ring, and completely get rid of the problem of uneven force on the left and right of the traditional down pressure steel design.
●HOP step-less adjustment allows for more fine-tuning; a larger HOP adjustment range makes it easy to control whether you use light flicks or heavy flicks.
●Adjustment ring is designed with a push-back spring to keep the HOP-UP not easy to loosen, effectively maintaining the ideal amount of depression after adjustment.

●This product provides: single HOP-UP chamber set (standard configuration is H.L.R. bucking, or replaceable T-HOP rubber) and Complete set (standard configuration isH.L.R. bucking, precision inner barrel, HOP chamber) available buy.
※Length below 220mm without air-cushion groove design※
​​※All retrofit kits are assembled by our professional technicians, but there may still be slight tolerances between different batches of airsoft guns. It is recommended that you must have relative DIY ability before purchasing.※

▲NOTICE▲
請勿過於用力調整，避免斷裂。
Please don't adjust too hard to avoid breakage.

※短內管無氣墊槽設計※
※Shorter barrel have no Air-cushion design (Shorter than 220mm)※

---

【T-N.T. ​THE ONE-WE GLOCK HOP-UP座 安裝注意事項】

他牌或進口品牌的早期內管，因窗口較小(膠皮內部下壓區較小)，調整環與膠皮內部下壓區會產生干涉，導致下壓不足的現象產生，玩家容易用力鎖緊調整環以增加下壓量，最後造成調整環斷裂。

現今市面上的精密內管窗口較大(膠皮內部下壓區較大)，可以提供更大的下壓面積與下壓量。建議有使用早期窗口較小的內管的玩家自行將窗口修大，再安裝我們THE ONE-WE GLOCK的HOP-UP座，才不會造成調整環斷裂。

【T-N.T. THE ONE-WE GLOCK HOP-UP chamber Installation Precautions】

The early inner barrels of other brands or imported brands have smaller windows (the lower pressure area inside the rubber is smaller). The adjustment ring and the pressure area inside the rubber will interfere, resulting in insufficient pressure. Players are prone to forcefully lock the adjustment ring in order to increase the amount of pressure, eventually causing the adjustment ring to break.

The precision inner barrels on the market today have larger windows (the internal pressure area of ​​​​the rubber is larger), which can provide a larger pressing area and amount. It is recommended that players who use early inner barrels with smaller windows repair the windows make it larger, then install T-N.T. THE ONE-WE GLOCK HOP-UP chamber, to avoid breaking the adjusting ring.

Browse photos

---

Specification:

• WE GLOCK 19 GBB RETROFIT KIT 86mm 
• WE GLOCK 17/18 GBB RETROFIT KIT 97mm 
• WE GLOCK 34 GBB RETROFIT KIT 112mm ​

※Length below 220mm without air-cushion groove design※

---

【標準-精密雙内徑氣墊內管】
STD. Precision Dual diameter Air-cushion inner barrel

​※220mm以下內管皆無氣墊槽設計※

※Length below 220mm without air-cushion groove design※

『THE ONE』 【WE GLOCK Retrofit Kit】86mm

NT$1,670.00

『THE ONE』 【WE GLOCK Retrofit Kit】97mm

NT$1,670.00

『THE ONE』 【WE GLOCK Retrofit Kit】112mm

NT$1,670.00

---

【S+ 精密雙内徑日蝕氣墊內管】
S+ Precision Dual diameter Air-cushion inner barrel

​※220mm以下內管皆無氣墊槽設計※

※Length below 220mm without air-cushion groove design※

『THE ONE』 【WE GLOCK Retrofit Kit】S+ 86mm

NT$1,870.00

『THE ONE』 【WE GLOCK Retrofit Kit】S+ 97mm

NT$1,870.00

『THE ONE』 【WE GLOCK Retrofit Kit】S+ 112mm

NT$1,870.00

---

【HOP-UP座 / 備用替換膠皮 / 配件】
HOP-UP CHAMBER, SPARE HOP-UP BUCKING, ACCESSORIES

『THE ONE』 【WE GLOCK HOP-UP Chamber set】

NT$1,120.00